Leave Your Message
How to Use Ratchet Lashing Straps Correctly?
News

How to Use Ratchet Lashing Straps Correctly?

2026-11-03

These Ratchet Lashing straps are manufactured to EN 12195‑2 and designedonly for cargo securing on vehicles, trailers and containers. They are NOT Lifting Slings and must never be used for overhead lifting, hoisting or suspending loads. The working load limit shown on the label is the Lashing Capacity (LC), not the Minimum Breaking Strength (MBS). MBS is typically twice the LC and represents the destructive test value, not the safe operating load. Always follow the marked LC for load planning.

Pre‑use Inspection (Mandatory before every application)

Examine the entire strap assembly carefully each time before use. Discard the strap immediately if any defect is found. Check the webbing first: stop using it if you spot cuts, deep abrasion, fraying, melted or hardened sections from heat, chemical stains, rotting stitching, or permanent deformation. The printed label must remain fully legible. Straps with missing or unreadable labels shall be taken out of service at once, because you can no longer confirm the rated capacity.

Inspect all metal components including the ratchet body, pawl, hooks and rings. Look for cracks, bending, opening deformation of hook throats, heavy corrosion and jammed moving parts. Test the release mechanism to make sure it engages and releases smoothly. Never use hardware that sticks or fails to lock securely.

Verify the anchor points on your truck, trailer or container. Only use factory‑designed lashing points rated for securing loads. Do not attach hooks to thin guardrails, bolt heads, makeshift welded tabs or other weak structures that may fail under tension. Check the cargo for sharp edges such as steel plate corners, extrusion cuts and casting burrs. Sharp edges will slice Polyester Webbing rapidly under load. Edge protectors or corner guards must be fitted wherever the strap crosses a sharp edge.

Correct Lashing Procedure

Lay out the webbing fully and make sure it runs flat with no twists, kinks or half‑turns. A twisted strap loses a large portion of its rated strength and concentrates wear at the twist point. Route the strap over or around the cargo, then attach both hooks to the selected anchor points. Hooks must seat fully and take load along their main axis. Side‑pulling on hooks or letting hook points bear against thin bars creates overload and risk of hook disengagement.

For over‑the‑top lashing, the most common style for palletised goods, the strap presses vertically onto the cargo and relies on friction to prevent sliding. For diagonal direct lashing, calculate load loss caused by the lashing angle. Avoid angles less than 30 degrees from the horizontal; the effective capacity drops sharply at shallow angles.

Open the ratchet handle fully to the flat release position. Thread the free end of the webbing underneath the central spindle of the ratchet drum. Pull manually to remove most slack before tensioning. Operate the ratchet handle back and forth to tighten the strap gradually. The webbing wound on the drum shall be no less than 1.5 turns and no more than 3 turns. Fewer wraps risk slipping; excessive wraps jam the ratchet and make release difficult.

Do NOT use pipes, crowbars or extension bars to lengthen the handle for extra leverage. EN 12195 limits manual tension force to approximately 50 daN. Extra leverage easily exceeds the design limit, overloading the webbing, hardware and anchor points. When the strap is tight enough, fold the ratchet handle fully closed so the pawl locks into place. Give a light test pull on the loose end to confirm positive locking. Fold and secure excess webbing to stop it flapping in the wind, rubbing against tyres or getting caught in moving parts during transit.

Safe Release Steps

Release the strap only after the vehicle is parked safely and the cargo is stable. Never stand directly in line with the tensioned strap. A snapped or suddenly released strap stores high elastic energy and can recoil violently, causing serious injury.

Hold the release tab on the ratchet, flip the handle all the way open to the 180‑degree flat position to disengage the pawl. Pull the webbing slowly and steadily to release tension gradually. Do not jerk or yank the strap free. If the cargo is tall, round or prone to tipping, add temporary supports before releasing lashings. After unloading, unhook both ends and straighten the webbing ready for storage.

In‑transit Checks & Limitations

Cargo often settles after the vehicle starts moving, which lets straps lose tension. Recheck and retighten straps after the first short section of travel. Inspect regularly on long journeys, especially over rough roads. Watch for shifting cargo, webbing creep and abrasion against sharp surfaces.

Keep polyester webbing away from hot exhausts, hot workpieces, open flame, strong acids and solvents. UV sunlight degrades polyester over time. Prolonged outdoor exposure weakens the webbing and shortens service life.

Strictly forbidden practices include: tying knots in the webbing (knots reduce strength drastically), stacking multiple straps onto one sharp corner, mixing straps of different rated LC in one securing system, using straps for lifting, and applying tension to twisted webbing.

Storage & Retirement

Store straps in a cool, dry, shaded area. Keep them off damp floors and away from oil, chemicals and direct sunlight. Do not drag straps over rough ground or sharp surfaces when moving them. Even if a strap looks intact, retire it once it shows heavy wear, heat damage or chemical contamination. Regular replacement prevents unexpected failure and keeps cargo transport compliant and safe.